[PATCH v6 2/3] virtio: pci support virtqueue reset

[Xuan Zhuo <xuanzhuo@linux.alibaba.com>]

PCI support virtqueue reset.

virtio_pci_common_cfg add "queue_reset" to support virtqueue reset.
The driver uses this to selectively reset the queue.

Signed-off-by: Xuan Zhuo <xuanzhuo@linux.alibaba.com>
---
 content.tex | 32 ++++++++++++++++++++++++++++++++
 1 file changed, 32 insertions(+)

diff --git a/content.tex b/content.tex
index dd095f4..3ac40db 100644
--- a/content.tex
+++ b/content.tex
@@ -901,6 +901,7 @@ \subsubsection{Common configuration structure layout}\label{sec:Virtio Transport
         le64 queue_driver;              /* read-write */
         le64 queue_device;              /* read-write */
         le16 queue_notify_data;         /* read-only for driver */
+        le16 queue_reset;               /* read-write */
 };
 \end{lstlisting}
 
@@ -980,6 +981,12 @@ \subsubsection{Common configuration structure layout}\label{sec:Virtio Transport
         may benefit from providing another value, for example an internal virtqueue
         identifier, or an internal offset related to the virtqueue number.
         \end{note}
+
+\item[\field{queue_reset}]
+        The driver uses this to selectively reset the queue.
+        This field exists only if VIRTIO_F_RING_RESET has been
+        negotiated. (see \ref{sec:Basic Facilities of a Virtio Device / Virtqueues / Virtqueue Reset}).
+
 \end{description}
 
 \devicenormative{\paragraph}{Common configuration structure layout}{Virtio Transport Options / Virtio Over PCI Bus / PCI Device Layout / Common configuration structure layout}
@@ -1021,6 +1028,22 @@ \subsubsection{Common configuration structure layout}\label{sec:Virtio Transport
 
 The device MUST present a 0 in \field{queue_enable} on reset.
 
+If VIRTIO_F_RING_RESET has been negotiated, the device MUST present a 0 in
+\field{queue_enable} after the driver has reset the virtqueue via
+\field{queue_reset}.
+
+If VIRTIO_F_RING_RESET has been negotiated, the device MUST present a 0 in
+\field{queue_reset} on reset.
+
+If VIRTIO_F_RING_RESET has been negotiated, the device MUST present a 0 in
+\field{queue_reset} after the virtqueue is enabled with \field{queue_enable}.
+
+The device MUST reset the queue when 1 is written to \field{queue_reset}, and
+present a 1 in \field{queue_reset} after the queue has been reset, until the
+driver re-enables the queue via \field{queue_enable} or the device is reset.
+The device MUST present consistent default values after queue reset.
+(see \ref{sec:Basic Facilities of a Virtio Device / Virtqueues / Virtqueue Reset}).
+
 The device MUST present a 0 in \field{queue_size} if the virtqueue
 corresponding to the current \field{queue_select} is unavailable.
 
@@ -1045,6 +1068,15 @@ \subsubsection{Common configuration structure layout}\label{sec:Virtio Transport
 
 The driver MUST NOT write a 0 to \field{queue_enable}.
 
+If VIRTIO_F_RING_RESET has been negotiated, after the driver writes 1 to
+\field{queue_reset} to reset the queue, it MUST verify that the queue
+has been reset by reading back \field{queue_reset} and ensuring that it
+is 1. The driver MAY re-enable the queue by writing a 1 to
+\field{queue_enable} after ensuring that the other virtqueue fields have
+been set up correctly. The driver MAY set driver-writeable queue configuration
+values to different values than those that were used before the queue reset.
+(see \ref{sec:Basic Facilities of a Virtio Device / Virtqueues / Virtqueue Reset}).
+
 \subsubsection{Notification structure layout}\label{sec:Virtio Transport Options / Virtio Over PCI Bus / PCI Device Layout / Notification capability}
 
 The notification location is found using the VIRTIO_PCI_CAP_NOTIFY_CFG
-- 
2.31.0