Re: [sca-assembly] [ISSUE 137]: Clarify the use of a binding name in areference target - Comment on Proposal

Works for me.  I presume the editors will deal with statement labels, etc.  It's good to work these in email so please send more comments.

Updates in the attached:

(See attached file: sca-assembly-1.1-spec-cd03+issue137b.doc)

Dave Booz

STSM, BPM and SCA Architecture

Co-Chair OASIS SCA-Policy TC and SCA-J TC

"Distributed objects first, then world hunger"

Poughkeepsie, NY (845)-435-6093  or  8-295-6093

e-mail:

Mike Edwards ---05/22/2009 11:28:49 AM---Folks, This is a comment on the proposal contained in

From:

Mike Edwards <>

To:



Date:

05/22/2009 11:28 AM

Subject:

[sca-assembly] [ISSUE 137]: Clarify the use of a binding name in a reference target - Comment on Proposal

Folks, 

This is a comment on the proposal contained in 

http://www.osoa.org/jira/secure/attachment/10500/sca-assembly-1.1-spec-cd03%2Bissue137.doc 

The bullet point about "bindingName" is not correct, in my opinion: 

"o        <binding-name> is the name of the service’s binding to use. If it is omitted, the SCA binding is used.> " 

There are a couple of cases to consider: 

a) There are multiple bindings, each with a name.  <binding-name> is specified. 

In this case, the binding-name value *MUST* match the name of one of the bindings.  If there is no match it is an error. 

b) There are multiple bindings, each with a name.  <binding-name> is not specified. 

In this case, the SCA runtime gets to choose which binding is used, in an implementation-dependent fashion. 

However, the selection of the binding must be with regard to the policies applied to both the reference and to the 

service binding.  The runtime *MUST NOT* select a binding which will fail due to policy mismatch between the 

reference and the service when another binding attached to the service will not fail due to policy mismatch. 

I suggest that the bullet point about <binding-name> is modified as follows: 

------------------------------- 

o <binding-name> is the name of a <binding/> of the service to use. 

If <binding-name> is present, the <binding/> subelement of the target service with @name corresponding to <binding-name> MUST be used 

for the wire.[ASM600xx] 

If there is no <binding/> subelement with @name corresponding to <binding-name>, the SCA runtime MUST raise an error. [ASM600xx] 

If <binding-name> is not present and the target service has multiple <binding/> subelements, the SCA runtime MUST choose one of the 

<binding/> elements to use for the wire which satisfies the mutual policy requirements of the reference and the service. [ASM600xx] 

-------------------------------- 

Yours,  Mike.

Strategist - Emerging Technologies, SCA & SDO.

Co Chair OASIS SCA Assembly TC.

IBM Hursley Park, Mail Point 146, Winchester, SO21 2JN, Great Britain.

Phone & FAX: +44-1962-818014    Mobile: +44-7802-467431  

Email:   

From: David Booz <> 

To:  

Date: 22/05/2009 13:37 

Subject: [sca-assembly] NEW ISSUE: Clarify the use of a binding name in a reference target

Note to Issue editor:

Please feel free to rename the attached document to match the issue# when attaching it to JIRA. Thanks.

TARGET: SCA Assembly PRD/CD03

DESCRIPTION: Reference targets can specify the name of a service binding

that should be used for invocations through that reference. This is described

in the spec here:

2786 by that target service. To do so, a wire target MAY be specified with a syntax of

2787 "componentName/serviceName/bindingName". [ASM90004]

The problem is that this capability is not described in the section on wires, which

only describes the "component/serviceName" formulation for a reference target.

PROPOSAL:

See attached Word document. My proposal is in section 5.4 ONLY. I don't know

why there are some many other things change marked.

(See attached file: sca-assembly-1.1-spec-cd03+issuexxx.doc)

Dave Booz

STSM, BPM and SCA Architecture

Co-Chair OASIS SCA-Policy TC and SCA-J TC

"Distributed objects first, then world hunger"

Poughkeepsie, NY (845)-435-6093 or 8-295-6093

e-mail:[attachment "sca-assembly-1.1-spec-cd03+issuexxx.doc" deleted by Mike Edwards/UK/IBM] ---------------------------------------------------------------------

To unsubscribe from this mail list, you must leave the OASIS TC that

generates this mail.  Follow this link to all your TCs in OASIS at:

https://www.oasis-open.org/apps/org/workgroup/portal/my_workgroups.php 

Unless stated otherwise above:

IBM United Kingdom Limited - Registered in England and Wales with number 741598. 

Registered office: PO Box 41, North Harbour, Portsmouth, Hampshire PO6 3AU 

sca-assembly-1.1-spec-cd03+issue137b.doc