On Wed, 13 Oct 2021 14:05:14 +0800, Jason Wang <> wrote:
> On Fri, Oct 1, 2021 at 1:50 AM Xuan Zhuo <> wrote:
> >
> > PCI support virtqueue reset.
> >
> > virtio_pci_common_cfg add "queue_reset" to support virtqueue reset.
> > The driver uses this to selectively reset the queue.
> >
> > Signed-off-by: Xuan Zhuo <>
> > ---
> > content.tex | 32 ++++++++++++++++++++++++++++++++
> > 1 file changed, 32 insertions(+)
> >
> > diff --git a/content.tex b/content.tex
> > index dd095f4..d014420 100644
> > --- a/content.tex
> > +++ b/content.tex
> > @@ -901,6 +901,7 @@ \subsubsection{Common configuration structure layout}\label{sec:Virtio Transport
> > le64 queue_driver; /* read-write */
> > le64 queue_device; /* read-write */
> > le16 queue_notify_data; /* read-only for driver */
> > + le16 queue_reset; /* read-write */
> > };
> > \end{lstlisting}
> >
> > @@ -980,6 +981,12 @@ \subsubsection{Common configuration structure layout}\label{sec:Virtio Transport
> > may benefit from providing another value, for example an internal virtqueue
> > identifier, or an internal offset related to the virtqueue number.
> > \end{note}
> > +
> > +\item[\field{queue_reset}]
> > + The driver uses this to selectively reset the queue.
> > + This field exists only if VIRTIO_F_RING_RESET has been
> > + negotiated. (see \ref{sec:Basic Facilities of a Virtio Device / Virtqueues / Virtqueue Reset}).
> > +
> > \end{description}
> >
> > \devicenormative{\paragraph}{Common configuration structure layout}{Virtio Transport Options / Virtio Over PCI Bus / PCI Device Layout / Common configuration structure layout}
> > @@ -1021,6 +1028,22 @@ \subsubsection{Common configuration structure layout}\label{sec:Virtio Transport
> >
> > The device MUST present a 0 in \field{queue_enable} on reset.
> >
> > +If VIRTIO_F_RING_RESET has been negotiated, the device MUST present a 0 in
> > +\field{queue_enable} after the driver has reset the virtqueue via
> > +\field{queue_reset}.
> > +
> > +If VIRTIO_F_RING_RESET has been negotiated, the device MUST present a 0 in
> > +\field{queue_reset} on reset.
> > +
> > +If VIRTIO_F_RING_RESET has been negotiated, the device MUST present a 0 in
> > +\field{queue_reset} after the virtqueue is enabled with \field{queue_enable}.
> > +
> > +The device MUST reset the queue when 1 is written to \field{queue_reset}, and
> > +present a 1 in \field{queue_reset} after the queue has been reset, until the
> > +driver re-enables the queue via \field{queue_enable} or the device is reset.
> > +The device MAY present different default values after queue reset.
>
> I'm not sure I get the meaning of this. The device should stick to
> consistent default values.
I do consider whether it is possible to allow the device to present different
default values at this time.
I thought about it carefully, it might cause some trouble. My
next version will emphasize that the same default values should be presented.
Thanks.
>
> Thanks
>
> > +(see \ref{sec:Basic Facilities of a Virtio Device / Virtqueues / Virtqueue Reset}).
> > +
> > The device MUST present a 0 in \field{queue_size} if the virtqueue
> > corresponding to the current \field{queue_select} is unavailable.
> >
> > @@ -1045,6 +1068,15 @@ \subsubsection{Common configuration structure layout}\label{sec:Virtio Transport
> >
> > The driver MUST NOT write a 0 to \field{queue_enable}.
> >
> > +If VIRTIO_F_RING_RESET has been negotiated, after the driver writes 1 to
> > +\field{queue_reset} to reset the queue, it MUST verify that the queue
> > +has been reset by reading back \field{queue_reset} and ensuring that it
> > +is 1. The driver MAY re-enable the queue by writing a 1 to
> > +\field{queue_enable} after ensuring that the other virtqueue fields have
> > +been set up correctly. The driver MAY set driver-writeable queue configuration
> > +values to different values than those that were used before the queue reset.
> > +(see \ref{sec:Basic Facilities of a Virtio Device / Virtqueues / Virtqueue Reset}).
> > +
> > \subsubsection{Notification structure layout}\label{sec:Virtio Transport Options / Virtio Over PCI Bus / PCI Device Layout / Notification capability}
> >
> > The notification location is found using the VIRTIO_PCI_CAP_NOTIFY_CFG
> > --
> > 2.31.0
> >
>
