Thanks Yves for the clarification.
Regards,
Ingo.
www.sdl.com
SDL PLC confidential, all rights reserved. If you are not the intended recipient of this mail SDL requests and requires that you delete it without acting upon or copying any of its contents,
and we further request that you advise us.
SDL PLC is a public limited company registered in England and Wales. Registered number: 02675207.
Registered address: Globe House, Clivemont Road, Maidenhead, Berkshire SL6 7DY, UK.
From: Yves Savourel [mailto:]
Sent: 07 September 2015 18:23
To: 'Dr. David Filip'
Cc: Ingo Prause;
Subject: RE: [xliff] Ignorables
Actually I think there is a small wording issue here:
The resegmentation PR says:
Only <segment> or <ignorable> elements
that have their canResegment value
resolved to yes MAY
be split.
And
Only <segment> or <ignorable> elements
that have their canResegment value
resolved to yes MAY
be join with other elements.
Which seems to assume ignorable has a canResegment attribute. But that is not the case.
We may want to re-word this (without changing the meaning).
So Ingo, I would say:
-
If the parent unit of the two ignorable elements resolves to ‘yes’ (i.e. is set to ‘yes’ or inherits ‘yes’) then you can join the two ignorable (following the PRs for
a join operation)
-
If the parent unit of the two ignorable elements resolves to ‘no’ (i.e. is set to ‘no’ or inherits ‘no’) then you cannot join the two ignorable elements.
Cheers,
-yves
From: [mailto:]
On Behalf Of Dr. David Filip
Sent: Monday, September 7, 2015 10:49 AM
To: Yves Savourel <>
Cc: Ingo Prause <>;
Subject: Re: [xliff] Ignorables
Sure, barring the segmentation being protected on higher levels, but this is also covered in the resegmentation PRs
http://docs.oasis-open.org/xliff/xliff-core/v2.0/xliff-core-v2.0.html#segmentationModification
Dr. David Filip
=======================
OASIS XLIFF TC Secretary, Editor, and Liaison Officer
LRC | CNGL | CSIS
University of Limerick, Ireland
telephone: +353-6120-2781
cellphone: +353-86-0222-158
facsimile: +353-6120-2734
http://www.cngl.ie/profile/?i=452
mailto:
On Mon, Sep 7, 2015 at 4:01 PM, Yves Savourel <> wrote:
Hum, it’s a good question.
There is a canResegment attribute that could prevent segments to be re-segmented. But its definition doesn’t explicitly
applies to ignorable elements.
So I’m not sure for that case. Input from other implementers would be great.
But for sure if there is no such attribute set to no on the parent unit, then yes, you can re-organize the ignorable
elements.
-yves
From: Ingo Prause [mailto:]
Sent: Monday, September 7, 2015 7:50 AM
To: Yves Savourel <>;
Subject: RE: [xliff] Ignorables
Hi Yves,
Thank you for your answer.
One more question – if you have two ignorables side-by-side, may they be merged together, or must they always remain independent items.
Thanks,
Ingo.
www.sdl.com
SDL PLC confidential, all rights reserved. If you are not the intended recipient of this mail SDL requests and requires that you delete
it without acting upon or copying any of its contents, and we further request that you advise us.
SDL PLC is a public limited company registered in England and Wales. Registered number:
02675207.
Registered address: Globe House, Clivemont Road, Maidenhead, Berkshire SL6 7DY, UK.
From: Yves
Savourel [mailto:]
Sent: 07 September 2015 14:36
To: Ingo Prause;
Subject: RE: [xliff] Ignorables
Hi Ingo,
Yes, you can have ignorable elements mixed anywhere with segment elements, including several side-by-side.
Usually ignorable would be used for non-translatabled “things” between segments. There are to some degree the
equivalent of the possible spans of content between <mrk mtype='seg'> of 1.2.
They have the same model as a <segment>, so you need to take them into account for any operation that goes across
all the parts of a <unit>, like re-ordering segments, computing non-translatable spans of content (the source of one ignorable can have a <sm translate='no'> that ends in two segments after for example), etc.
I hope this helps,
-yves
From:
[mailto:]
On Behalf Of Ingo Prause
Sent: Monday, September 7, 2015 7:05 AM
To:
Subject: [xliff] Ignorables
Hi,
I have a question about ignorables.
Can you have two ignorables side-by-side (or would you usually just have one at start/between segments/or at end and what are the processing requirements for ignorables?
Thanks,
Ingo.
Ingo Prause
| Principal Developer | SDL | (t) +353 (01) 20 50 305
SDL Global Solutions (Ireland) Limited | La Vallee House, Upper Dargle Road, Bray, Co. Wicklow, Ireland | Registered in Ireland, Number 135925
www.sdl.com
SDL PLC confidential, all rights reserved. If you are not the intended recipient of this mail SDL requests and requires that you delete
it without acting upon or copying any of its contents, and we further request that you advise us.
SDL PLC is a public limited company registered in England and Wales. Registered number:
02675207.
Registered address: Globe House, Clivemont Road, Maidenhead, Berkshire SL6 7DY, UK.
This message has been scanned for malware by Websense.
www.websense.com
Click
here to report this email as spam.
